Skip to main content
Field GuideMaintenance

Dryer Hose Replacement: When the Hose Behind Your Dryer Needs Replacing

Dryer vent hose replacement in NYC: how to tell the hose behind your dryer is crushed or wrong, what code requires, and our $49.99 installed swap.

By The Vent Pro NYC TeamPublished November 20, 20266 min read

The hose behind your dryer is called the transition duct. It's the short, flexible piece that connects the back of the dryer to the vent pipe in the wall or floor. It gets pushed, bent and stepped on more than any other part of the vent, so it's usually the first part to fail. When it does, the fix is simple: we take the old one off and install a new semi-rigid aluminum transition duct for $49.99, installed. We only do it with your approval, and most of the time it happens during a regular cleaning visit.

This guide is about recognizing a hose that needs replacing. If you want the longer comparison of vinyl, foil, semi-rigid and rigid metal, read our guide to flexible dryer hose vs rigid metal duct.

What is the hose behind the dryer, exactly?

A dryer vent has two parts:

  • The transition duct. The short hose from the dryer's exhaust outlet to the wall. It has to flex so the dryer can be pulled out for service.
  • The vent run. The fixed duct that carries the exhaust from the wall to the cap outside. In NYC that run has to be metal, at least 0.016 inch thick (NYC Mechanical Code §504.8.1).

When people search for "dryer exhaust hose installation" or "dryer vent hose replacement," they almost always mean the first part. It's a small piece, but every bit of hot, wet, lint-heavy air from the dryer goes through it.

How do I know my dryer hose needs replacing?

Pull the dryer forward a foot or so and look behind it with a flashlight. Replace the hose if you see any of these:

  • It's crushed or kinked. The most common one. The dryer got pushed back flush against the wall and folded the hose flat. A crushed hose chokes the airflow even if the rest of the vent is clean.
  • It's white vinyl or plastic. We replace these.
  • It's thin foil. The kind that dents when you touch it and tears easily.
  • It's torn or has holes. Any gap lets hot, linty air blow into the space behind the dryer.
  • It's come loose. The hose has slipped off the dryer outlet or off the wall connection, so the dryer is exhausting into the room.
  • There's lint on the floor or the wall behind the dryer. Lint outside the hose means air is escaping somewhere it shouldn't.
  • It's sagging in a low loop. Extra hose length droops, and the low spot collects lint and moisture.

Indoor signs point the same way: loads that need two cycles, a laundry room that gets hot and humid, or a dryer that's hot to the touch. Our post on why a dryer takes two cycles walks through those.

What does NYC code say about the dryer transition hose?

New York City writes its own mechanical code, and clothes dryer exhaust is covered in §504. For the hose specifically, §504.8.3 requires that the transition duct be listed to UL 2158A, the safety standard for clothes dryer transition duct. The fixed run in the wall is a separate requirement, and it has to be metal (§504.8.1).

Outside the city, on Long Island and in New Jersey, a different code applies, so we don't quote section numbers for those areas.

What do you install when you replace the hose?

A semi-rigid aluminum transition duct. It holds its round shape better than foil, it's easy to route in a gentle curve, and it's what we put in on almost every replacement. The price is $49.99, installed.

Here's how it works on a visit:

  1. We pull the dryer out and inspect the old hose before we touch anything.
  2. If it needs replacing, we tell you why and show you. Nothing gets swapped without your OK.
  3. We clean the full vent run from the dryer to the outside cap, then fit the new hose, cut to a sensible length with no sag and no sharp bends.
  4. We push the dryer back carefully so the new hose isn't crushed, and take a second airflow reading.

Most visits are done in under an hour, and you get a written before-and-after report with photos.

Why won't you install a slim "periscope" duct?

Periscope ducts are the flat, rectangular adapters sold for tight spaces so the dryer can sit closer to the wall. We don't install them. Their narrow, flattened shape clogs with lint fast, which is the opposite of what you want from a vent.

If the space is really tight, we'll talk you through the options: semi-rigid aluminum routed carefully, or a rigid metal connection that we quote on site after we see the space.

What if the problem is past the hose?

Sometimes the hose is fine and the damage is further along: a crushed section inside the wall, a disconnected joint in the ceiling, a broken outside cover, or a dryer that was moved and needs new venting. Those aren't a $49.99 swap. They're quoted separately.

The fastest way to get a quote is to text a photo to (718) 541-5567. Our repair and installation page explains how it works, and our post on dryer vent duct repair and replacement covers what those jobs usually involve.

How much does it cost all together?

What Price
Total Home Protection cleaning (basement or 1st floor) from $199.99
Semi-rigid aluminum transition duct, installed $49.99
Rigid metal connection, or repairs past the hose Quoted first

Cleaning prices are flat: a long vent costs the same as a short one, and we never charge by the foot. The booking page shows the exact total for your ZIP before you pay. The hose is only added if you approve it on the day.

We're a family-owned company based in Brooklyn, so you deal directly with the people doing the work, and the quote you hear on the day is the price you pay.

Frequently asked questions

Can I replace the dryer hose myself?

Yes, if you're comfortable pulling the dryer out. Use a transition duct listed to UL 2158A, keep it short, avoid sharp bends, and don't crush it when you push the dryer back. If the vent run itself hasn't been cleaned in a while, a new hose on a clogged vent won't fix the airflow.

Do I need a cleaning to get the hose replaced?

The hose swap is an add-on, so it's usually done during a cleaning visit. It makes sense to do both at once: the dryer is already pulled out, and a new hose on a dirty vent only solves half the problem.

How often should the hose be replaced?

There's no fixed schedule. Replace it when it's crushed, torn, disconnected or the wrong material. We check it at every cleaning, and most households should have the vent cleaned once a year.

My dryer is on the 2nd floor. Does the hose cost more?

No. The hose is $49.99 installed on any floor. The cleaning itself costs more for a dryer on the 2nd floor or higher, and the booking page shows the exact total for your address.

Vent Pro NYC

Family-owned. Brooklyn-based. Fully insured.

Most hose swaps happen during a cleaning visit: $49.99 installed, only with your approval. For anything bigger, text a photo to (718) 541-5567 for a quote.